meta data for this page
Differences
This shows you the differences between two versions of the page.
Next revision | Previous revisionLast revisionBoth sides next revision | ||
home_automation:esp8266:espeasy [2016/06/02 06:01] – created niziak | home_automation:esp8266:espeasy [2016/06/02 06:55] – niziak | ||
---|---|---|---|
Line 1: | Line 1: | ||
====== ESP Easy ====== | ====== ESP Easy ====== | ||
+ | ===== First setup ===== | ||
+ | |Wifi ssid | ESP_0 | | ||
+ | |Wifi pass | configesp | | ||
+ | |||
===== Emergency reset ===== | ===== Emergency reset ===== | ||
- | During power up, if TX & RX lines are tied together. | + | During power up, if TX & RX lines are tied together.\\ |
- | Device is sending two bytes (115200 speed): 0xAA 0x55 and after 1ms checks if two the sames bytes are received. | + | Device is sending two bytes (115200 speed): 0xAA 0x55 and after 1ms checks if two the sames bytes are received, and resets device to factory settings. |
+ | |||
+ | ===== Delayed reset ===== | ||
+ | When failed connection tries reach 30, system is performing delayed reset (after 60 seconds). | ||
+ | Function '' | ||
+ | |||
+ | < | ||
+ | |||
+ | ===== rst cause ===== | ||
+ | |||
+ | ^ Number ^ Description | ||
+ | | 0 | unknown | ||
+ | | 1 | normal boot | | ||
+ | | 2 | reset pin | | ||
+ | | 3 | software reset | | ||
+ | | 4 | watchdog reset | | ||
+ | |||
+ | ===== boot mode ===== | ||
+ | the first value respects the pin setup of the Pins 0, 2 and 15. | ||
+ | |||
+ | ^ Number ^ GPIO15 ^ GPIO0 ^ GPIO2 ^ Mode | | ||
+ | | 0 | 0V | 0V | 0V | Not valid | | ||
+ | | 1 | 0V | 0V | 3.3V | Uart | | ||
+ | | 2 | 0V | 3.3V | 0V | Not valid | | ||
+ | | 3 | 0V | 3.3V | 3.3V | Flash | | ||
+ | | 4 | 3.3V | 0V | 0V | SDIO | | ||
+ | | 5 | 3.3V | 0V | 3.3V | SDIO | | ||
+ | | 6 | 3.3V | 3.3V | 0V | SDIO | | ||
+ | | 7 | 3.3V | 3.3V | 3.3V | SDIO | | ||
+ | |||
+ | note: | ||
+ | * '' | ||
+ | |||
+ | ===== Serial commands ===== | ||
+ | Maintenance: | ||
+ | ^ command | ||
+ | ^ Maintenance | ||
+ | | TaskClear | ||
+ | | wdconfig | ||
+ | | wdread | ||
+ | | VariableSet | ||
+ | | build | build_num | ||
+ | | NoSleep | ||
+ | | Reboot | ||
+ | | Restart | ||
+ | ^ Domoticz old ^^^ | ||
+ | | DomoticzSend | ||
+ | | DomoticzGet | ||
+ | ^ Configuration | ||
+ | | WifiSSID | ||
+ | | WifiKey | ||
+ | | WifiScan | ||
+ | | WifiConnect | ||
+ | | WifiDisconnect | | | | ||
+ | | Delay | seconds | ||
+ | | Debug | level | | | ||
+ | | IP | ip address | ||
+ | | Settings | ||
+ | | Save | ||
+ | | Load | ||
+ | | FlashDump | ||
+ | ^ Flash ^^^ | ||
+ | | Erase | | Erase flash, disconnect WiFi | | ||
+ | | Reset | | ResetFactory() | | ||
+ | | flashcheck | ||
+ | | ||
===== Firmware build ===== | ===== Firmware build ===== | ||