meta data for this page

Aoostar R7

Product page: AOOSTAR R7 2 Bay 40T NAS Storage AMD Ryzen 7 5825U Mini PC

Details:

  • AMD Ryzen 7 5825U 8C/16T 7nm 2.0GHz (up to 4.5GHz)
    • AMD Socket FP6
    • supports 2 ch x 32GB ECC
    • Ryzen 7(Zen 3 (Cezanne))
  • 3 Displays:
    • HDMI
    • DP
    • USB-C
  • USB-PD sink
  • 2 x SODIMM socket for DDR4 3200MHz 2x SODIMM sockets
  • 2 x socket for M.2 NVME
  • 1 x M.2 Socket with WIFi 6 / BT5.2 card (2 flex antenna glued inside)
    • Network controller: Intel Corporation Wi-Fi 6 AX200 (rev 1a)
  • 2 x 3,5“ HDD SATA
  • 2 x 2.5 Gbps LAN ports
    • Intel Corporation Ethernet Controller I226-V
  • 2 x USB3.0
  • 2 x USB2.0

Very loud bottom fan, 2 pin only, connected to 4pin connector on MB.

  • EVerflow Model: R1292215BL
  • 92 x 92 x 16 [mm]
  • 12V / 0.20A
  • Replacement Noctua NF-A9x14 PWM
    • 12V / 1.32W / 0.11A
    • 92 x 92 x 14 [mm]
    • 19,9 dBa
    • 50.5 CFM
    • 2200 rpm

ECC RAM

Running on Hynix DDR4 32 GB 3200MHz CL22 (HMAA4GS7AJR8N-XN). But no EDAC driver loaded in Kernel.

Linux

lm-sensors

No driver for ITE IT8613e?

# sensors
iwlwifi_1-virtual-0
Adapter: Virtual device
temp1:            N/A  
 
nvme-pci-0100
Adapter: PCI adapter
Composite:    +40.9°C  (low  = -273.1°C, high = +81.8°C)
                       (crit = +84.8°C)
Sensor 1:     +40.9°C  (low  = -273.1°C, high = +65261.8°C)
Sensor 2:     +47.9°C  (low  = -273.1°C, high = +65261.8°C)
 
amdgpu-pci-0500
Adapter: PCI adapter
vddgfx:      718.00 mV 
vddnb:       768.00 mV 
edge:         +36.0°C  
PPT:           4.00 W  
 
k10temp-pci-00c3
Adapter: PCI adapter
Tctl:         +37.2°C  

Build under Proxmox host

# enable non-subscription PVE repo
# and then:
 
apt install proxmox-headers-6.8
 
 
# Install dev tools:
apt install git dkms make
 
# Clone repo
cd /usr/src
git clone https://github.com/frankcrawford/it87.git
cd it87
make dkms
dkms autoinstall
modprobe it87
[  575.844856] it87: module verification failed: signature and/or required key missing - tainting kernel
[  575.845508] it87: it87 driver version v1.0-169-g213db3a.20240922
[  575.845597] it87: Found IT8613E chip at 0xa30, revision 8
[  575.845622] it87: Beeping is supported
# sensors
it8613-isa-0a30
Adapter: ISA adapter
in0:         682.00 mV (min =  +2.07 V, max =  +2.24 V)
in1:           1.25 V  (min =  +1.16 V, max =  +2.54 V)
in2:           1.02 V  (min =  +1.33 V, max =  +1.62 V)
in4:           1.67 V  (min =  +1.54 V, max =  +1.86 V)
in5:           2.53 V  (min =  +2.11 V, max =  +0.62 V)
3VSB:         66.00 mV (min =  +0.62 V, max =  +2.09 V)
Vbat:          3.17 V  
+3.3V:         3.30 V  
fan2:         615 RPM  (min =   90 RPM)
fan3:           0 RPM  (min =   13 RPM)
fan4:           0 RPM  (min =   -1 RPM)
fan5:           0 RPM  (min =   -1 RPM)
temp1:        -55.0°C  (low  = -79.0°C, high = +121.0°C)  sensor = thermistor
temp2:        -55.0°C  (low  = +79.0°C, high = +41.0°C)
temp3:        +28.0°C  (low  = -34.0°C, high = -65.0°C)
intrusion0:  ALARM