meta data for this page
Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revisionLast revisionBoth sides next revision | ||
| nsa310:debian [2020/04/18 18:54] – niziak | hw:nsa310:debian [2020/11/06 11:42] – niziak | ||
|---|---|---|---|
| Line 2: | Line 2: | ||
| ====== References ====== | ====== References ====== | ||
| + | |||
| OpenWRT packages: [[http:// | OpenWRT packages: [[http:// | ||
| Line 14: | Line 15: | ||
| [[http:// | [[http:// | ||
| - | ====== Serial converter ====== | ||
| - | |||
| - | 3,3V level converter | ||
| - | 115200 8N1 | ||
| - | |||
| - | ^ 1 ^ 2 ^ 3 ^ 4 ^ 5 ^ | ||
| - | |Vcc | RX | TX | nc | GND | | ||
| - | |||
| - | < | ||
| - | | ||
| - | | \/ | __ _ _ ____ | ||
| - | | |\/| |/ _` | '__\ \ / / _ \ | | | ||
| - | | | | | (_| | | \ V / __/ | | | ||
| - | |_| |_|\__, | ||
| - | | ||
| - | | | | | | __ ) ___ ___ | |_ | ||
| - | | | | |___| _ \ / _ \ / _ \| __| | ||
| - | | |_| |___| |_) | (_) | (_) | |_ | ||
| - | | ||
| - | ** MARVELL BOARD: RD-88F6281A LE | ||
| - | |||
| - | U-Boot 1.1.4 (Jun 8 2011 - 18:48:37) Marvell version: 3.4.19 | ||
| - | |||
| - | U-Boot code: 00600000 -> 0067FFF0 | ||
| - | |||
| - | Soc: 88F6281 A1 (DDR2) | ||
| - | CPU running @ 1200Mhz L2 running @ 400Mhz | ||
| - | SysClock = 400Mhz , TClock = 200Mhz | ||
| - | |||
| - | DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6 | ||
| - | DRAM CS[0] base 0x00000000 | ||
| - | DRAM Total size 256MB 16bit width | ||
| - | Addresses 10M - 0M are saved for the U-Boot usage. | ||
| - | Mem malloc Initialization (10M - 7M): Done | ||
| - | NAND:128 MB | ||
| - | Flash: | ||
| - | |||
| - | CPU : Marvell Feroceon (Rev 1) | ||
| - | Kernel address is 0x4640000. | ||
| - | |||
| - | Streaming disabled | ||
| - | Write allocate disabled | ||
| - | |||
| - | Module 0 is RGMII | ||
| - | Module 1 is TDM | ||
| - | |||
| - | USB 0: host mode | ||
| - | PEX 0: PCI Express Root Complex Interface | ||
| - | PEX interface detected Link X1 | ||
| - | Net: | ||
| - | Hit any key to stop autoboot: | ||
| - | |||
| - | </ | ||
| ====== Preparation ===== | ====== Preparation ===== | ||
| Line 243: | Line 191: | ||
| ====== Own kernel ====== | ====== Own kernel ====== | ||
| - | here's no need to keep pestering the poor guy over simple config changes. It's easy to build your own kernel; the instructions are right there in the first post. On a debian host you need to add the emdebian repo and install gcc-4.7-arm-linux-gnueabi (or whatever version) and u-boot-tools to build the kernel. | + | There's no need to keep pestering the poor guy over simple config changes. It's easy to build your own kernel; the instructions are right there in the first post. On a debian host you need to add the emdebian repo and install gcc-4.7-arm-linux-gnueabi (or whatever version) and u-boot-tools to build the kernel. |
| I just built one with device mapper and crypto target support, and threw in netfilter NAT stuff for giggles. | I just built one with device mapper and crypto target support, and threw in netfilter NAT stuff for giggles. | ||
| Line 255: | Line 203: | ||
| Download lastest Jessie rootfs from: [[http:// | Download lastest Jessie rootfs from: [[http:// | ||
| - | Or locally: {{: | + | Or locally: {{hw: |
| Unpack rootfs to media, can be USB pendrive for now. | Unpack rootfs to media, can be USB pendrive for now. | ||
| Line 298: | Line 246: | ||
| ===== Boot with Flattened Device Tree ===== | ===== Boot with Flattened Device Tree ===== | ||
| - | **NOT SUPPORTED BY OLD (default U-BOOT** | + | **NOT SUPPORTED BY OLD (default U-BOOT)** |
| < | < | ||
| cd boot | cd boot | ||
| Line 330: | Line 278: | ||
| - kirkwood-nsa310a.dtb - like above but without red USB led, and sensor device ' | - kirkwood-nsa310a.dtb - like above but without red USB led, and sensor device ' | ||
| - | My NSA310 version is like nsa310 but with lm85 :), so I've created {{: | + | My NSA310 version is like nsa310 but with lm85 :), so I've created {{hw: |
| < | < | ||